Allow the user to configure needed_{head,tail}room for both netkit
devices. The idea is similar to 163e529200af ("veth: implement
ndo_set_rx_headroom") with the difference that the two parameters
can be specified upon device creation. By default the current behavior
stays as is which is needed_{head,tail}room is 0.
In case of Cilium, for example, the netkit devices are not enslaved
into a bridge or openvswitch device (rather, BPF-based redirection
is used out of tcx), and as such these parameters are not propagated
into the Pod's netns via peer device.
Given Cilium can run in vxlan/geneve tunneling mode (needed_headroom)
and/or be used in combination with WireGuard (needed_{head,tail}room),
allow the Cilium CNI plugin to specify these two upon netkit device
creation.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/bpf/20241220234658.490686-1-daniel@iogearbox.net
Signed-off-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Add support for the independent control state machine per IEEE
802.1AX-2008 5.4.15 in addition to the existing implementation of the
coupled control state machine.
Introduces two new states, AD_MUX_COLLECTING and AD_MUX_DISTRIBUTING in
the LACP MUX state machine for separated handling of an initial
Collecting state before the Collecting and Distributing state. This
enables a port to be in a state where it can receive incoming packets
while not still distributing. This is useful for reducing packet loss when
a port begins distributing before its partner is able to collect.
Added new functions such as bond_set_slave_tx_disabled_flags and
bond_set_slave_rx_enabled_flags to precisely manage the port's collecting
and distributing states. Previously, there was no dedicated method to
disable TX while keeping RX enabled, which this patch addresses.
Note that the regular flow process in the kernel's bonding driver remains
unaffected by this patch. The extension requires explicit opt-in by the
user (in order to ensure no disruptions for existing setups) via netlink
support using the new bonding parameter coupled_control. The default value
for coupled_control is set to 1 so as to preserve existing behaviour.
Signed-off-by: Aahil Awatramani <aahila@google.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20240202175858.1573852-1-aahila@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make the broadcast cutoff configurable through netlink. Note
that macvlan is weird because there is no central device for
us to configure (the lowerdev could be anything). So all the
options are duplicated over what could be thousands of child
devices.
IFLA_MACVLAN_BC_QUEUE_LEN took the approach of taking the maximum
of all child device settings. This is unnecessary as we could
simply store the option in the port device and take the last
child device that gets updated as the value to use.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add per port priority support for bonding active slave re-selection during
failover. A higher number means higher priority in selection. The primary
slave still has the highest priority. This option also follows the
primary_reselect rules.
This option could only be configured via netlink.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New netlink attributes IFLA_TSO_MAX_SIZE and IFLA_TSO_MAX_SEGS
are used to report to user-space the device TSO limits.
ip -d link sh dev eth1
...
tso_max_size 65536 tso_max_segs 65535
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add a new bonding option ns_ip6_target, which correspond
to the arp_ip_target. With this we set IPv6 targets and send IPv6 NS
request to determine the health of the link.
For other related options like the validation, we still use
arp_validate, and will change to ns_validate later.
Note: the sysfs configuration support was removed based on
https://lore.kernel.org/netdev/8863.1645071997@famine
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet suggested to allow users to modify max GRO packet size.
We have seen GRO being disabled by users of appliances (such as
wifi access points) because of claimed bufferbloat issues,
or some work arounds in sch_cake, to split GRO/GSO packets.
Instead of disabling GRO completely, one can chose to limit
the maximum packet size of GRO packets, depending on their
latency constraints.
This patch adds a per device gro_max_size attribute
that can be changed with ip link command.
ip link set dev eth0 gro_max_size 16000
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Coco Li <lixiaoyan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we use hard code number to verify if we are in the
arp_interval timeslice. But some user may want to reduce/extend
the verify timeslice. With the similar team option 'missed_max'
the uers could change that number based on their own environment.
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel provides a "/proc/sys/net/ipv6/conf/<iface>/mtu"
file, which can temporarily record the mtu value of the last
received RA message when the RA mtu value is lower than the
interface mtu, but this proc has following limitations:
(1) when the interface mtu (/sys/class/net/<iface>/mtu) is
updeated, mtu6 (/proc/sys/net/ipv6/conf/<iface>/mtu) will
be updated to the value of interface mtu;
(2) mtu6 (/proc/sys/net/ipv6/conf/<iface>/mtu) only affect
ipv6 connection, and not affect ipv4.
Therefore, when the mtu option is carried in the RA message,
there will be a problem that the user sometimes cannot obtain
RA mtu value correctly by reading mtu6.
After this patch set, if a RA message carries the mtu option,
you can send a netlink msg which nlmsg_type is RTM_GETLINK,
and then by parsing the attribute of IFLA_INET6_RA_MTU to
get the mtu value carried in the RA message received on the
inet6 device. In addition, you can also get a link notification
when ra_mtu is updated so it doesn't have to poll.
In this way, if the MTU values that the device receives from
the network in the PCO IPv4 and the RA IPv6 procedures are
different, the user can obtain the correct ipv6 ra_mtu value
and compare the value of ra_mtu and ipv4 mtu, then the device
can use the lower MTU value for both IPv4 and IPv6.
Signed-off-by: Rocco Yue <rocco.yue@mediatek.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210827150412.9267-1-rocco.yue@mediatek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an option lacp_active, which is similar with team's runner.active.
This option specifies whether to send LACPDU frames periodically. If set
on, the LACPDU frames are sent along with the configured lacp_rate
setting. If set off, the LACPDU frames acts as "speak when spoken to".
Note, the LACPDU state frames still will be sent when init or unbind port.
v2: remove module parameter
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 9ab7e76aefc97a9aa664accb59d6e8dc5e52514a.
This patch was committed without maintainer approval and despite a number
of unaddressed concerns from review. There are several issues that
impede the acceptance of this patch and that make a reversion of this
particular instance of these changes the best way forward:
i) the patch contains several logically separate changes that would be
better served as smaller patches (for review purposes)
ii) functionality like the handling of end markers has been introduced
without further explanation
iii) symmetry between the handling of GTPv0 and GTPv1 has been
unnecessarily broken
iv) the patchset produces 'broken' packets when extension headers are
included
v) there are no available userspace tools to allow for testing this
functionality
vi) there is an unaddressed Coverity report against the patch concering
memory leakage
vii) most importantly, the patch contains a large amount of superfluous
churn that impedes other ongoing work with this driver
This patch will be reworked into a series that aligns with other
ongoing work and facilitates review.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Following patch add support for flow based tunneling API
to send and recv GTP tunnel packet over tunnel metadata API.
This would allow this device integration with OVS or eBPF using
flow based tunneling APIs.
Signed-off-by: Pravin B Shelar <pbshelar@fb.com>
Link: https://lore.kernel.org/r/20210110070021.26822-1-pbshelar@fb.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Background:
Broadcast and multicast packages are enqueued for later processing.
This queue was previously hardcoded to 1000.
This proved insufficient for handling very high packet rates.
This resulted in packet drops for multicast.
While at the same time unicast worked fine.
The change:
This patch make the queue length adjustable to accommodate
for environments with very high multicast packet rate.
But still keeps the default value of 1000 unless specified.
The queue length is specified as a request per macvlan
using the IFLA_MACVLAN_BC_QUEUE_LEN parameter.
The actual used queue length will then be the maximum of
any macvlan connected to the same port. The actual used
queue length for the port can be retrieved (read only)
by the IFLA_MACVLAN_BC_QUEUE_LEN_USED parameter for verification.
This will be followed up by a patch to iproute2
in order to adjust the parameter from userspace.
Signed-off-by: Thomas Karlsson <thomas.karlsson@paneda.se>
Link: https://lore.kernel.org/r/dd4673b2-7eab-edda-6815-85c67ce87f63@paneda.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds a new port attribute, IFLA_BRPORT_MRP_IN_OPEN, which
allows to notify the userspace when the node lost the contiuity of
MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new port attribute, IFLA_BRPORT_MRP_RING_OPEN, which allows
to notify the userspace when the port lost the continuite of MRP frames.
This attribute is set by kernel whenever the SW or HW detects that the ring is
being open or closed.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new netlink attribute to allow a user to (optionally)
specify the desired offload mode immediately upon MACSec link creation.
Separate iproute patch will be required to support this from user space.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new MACsec offloading option, MACSEC_OFFLOAD_MAC,
allowing a user to select a MAC as a provider for MACsec offloading
operations.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the macsec_context structure. It will be used
in the kernel to exchange information between the common MACsec
implementation (macsec.c) and the MACsec hardware offloading
implementations. This structure contains pointers to MACsec specific
structures which contain the actual MACsec configuration, and to the
underlying device (phydev for now).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, gratuitous ARP/ND packets are sent every `miimon'
milliseconds. This commit allows a user to specify a custom delay
through a new option, `peer_notif_delay'.
Like for `updelay' and `downdelay', this delay should be a multiple of
`miimon' to avoid managing an additional work queue. The configuration
logic is copied from `updelay' and `downdelay'. However, the default
value cannot be set using a module parameter: Netlink or sysfs should
be used to configure this feature.
When setting `miimon' to 100 and `peer_notif_delay' to 500, we can
observe the 500 ms delay is respected:
20:30:19.354693 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:19.874892 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:20.394919 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
20:30:20.914963 ARP, Request who-has 203.0.113.10 tell 203.0.113.10, length 28
In bond_mii_monitor(), I have tried to keep the lock logic readable.
The change is due to the fact we cannot rely on a notification to
lower the value of `bond->send_peer_notif' as `NETDEV_NOTIFY_PEERS' is
only triggered once every N times, while we need to decrement the
counter each time.
iproute2 also needs to be updated to be able to specify this new
attribute through `ip link'.
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
sync with latest bpf-next tree.
the include/linux/filter.h is created as libbpf.c tries
to use various insn define macros.
Signed-off-by: Yonghong Song <yhs@fb.com>
